Hardrace RC Front Lower Control Arm – Honda City / Fit / Jazz
€917.68 Original price was: €917.68.€780.03Current price is: €780.03.
Pillow Ball Equipped
Roll Center Adjuster
2 PCS/SET
Available – Delivery within 15 days
Hardrace RC Front Lower Control Arm – Honda City / Fit / Jazz (Q0241)
Product Overview
While the Honda Fit and Jazz are celebrated for their nimble handling and lightweight chassis, their front MacPherson strut layout is highly sensitive to ride-height modifications. When you lower these vehicles on performance lowering springs or track coilovers, the factory front lower control arms tilt sharply upward. This geometry distortion drops the vehicle’s structural roll center below the ground, introducing excessive body roll and unpredictable front toe-out as the suspension compresses.
The Hardrace RC Front Lower Control Arm Kit (Q0241) is a heavy-duty, track-targeted suspension solution engineered specifically to fix these geometry flaws. Available at JDMaster.net, these high-strength control arms are manufactured from ultra-rigid hardened steel alloy and come pre-assembled with integrated Roll Center (RC) Adjuster ball joints and high-durometer hardened rubber bushings. By dropping the outer suspension pivot points back down into their mathematically optimal plane, this kit restores ideal tracking mechanics, giving your Honda instantaneous steering response and maximized front-tire adhesion under heavy cornering loads.
Key Features & Benefits
-
Integrated Roll Center Correction: Features extended-shank lower ball joints that level out the control arm angle on lowered vehicles, raising the roll center closer to the center of gravity to minimize body roll.
-
Eliminates Dynamic Bump-Steer: Keeps the front steering tie-rods and control arms moving along synchronized, parallel arcs, preventing abrupt, unwanted toe alignment shifts when compressing over mid-corner road contours.
-
High-Durometer Hardened Rubber Bushings: Equipped with premium, solid vulcanized rubber bushings that deliver a massive reduction in compliance over soft factory rubber while absorbing harsh road vibrations.
-
Reinforced Hardened Steel Alloy: Fabricated from thick-walled, ultra-high-strength steel plates that completely resist twisting and mechanical warping under intense lateral grip and racing loads.
-
Crisp, Linear Steering Feedback: Minimizing structural arm and bushing deflection creates a highly direct mechanical bond between your front subframe and the knuckles for sharp, predictable turn-in.
-
ED Anti-Corrosion Finish: Treated with Hardrace’s signature Electrophoretic Deposition (ED) base layer and industrial outer paint to provide a durable barrier against stone chips, salt, and track grit.
Technical Specifications
| Feature | Specification |
| Brand | Hardrace |
| Part Number / SKU | Q0241 |
| Product Type | Hardened Steel Front Lower Control Arms with RC Adjusters |
| Bushing Configuration | High-Hardness, Solid Vulcanized Hardened Rubber |
| Ball Joint Profile | Pre-Installed Extended Stem Roll Center (RC) Ball Joints |
| Material Base | Ultra-High-Strength Reinforced Steel Alloy |
| Piece Count | 2 Pieces / Set (Complete Front Axle Left & Right Arms) |
| Finish Protection | Industrial Anti-Rust Electrophoretic Deposition (ED) Coating |
| Maintenance Profile | Sealed ball joints with high-elasticity protective dust boots |
| Installation Status | Direct OE replacement (Full tracking alignment mandatory) |
Applications
-
Honda Fit / Jazz (2008–2014 2nd Generation — GE6 / GE7 / GE8 / GE9 Chassis)
-
Honda Fit / Jazz Hybrid (2010–2014 2nd Generation — GP1 / GP4 Chassis)
-
Honda City (2008–2014 5th Generation — GM2 / GM3 Chassis)
The Mechanical Advantage: Restoring MacPherson Strut Efficiency
On a standard MacPherson strut design like that of the GE8 Fit/Jazz, the lower control arm acts as the primary mechanical anchor for the wheel hub. When the car is lowered without structural correction, the arm tilts past its horizontal horizontal line. When you throw the car into a hard corner, the suspension compresses further into a positive camber curve, which lifts the inner edge of the tire off the tarmac and severely shrinks your contact patch.
The Hardrace Q0241 kit addresses this bottleneck on two fronts. First, the extended-stem roll center ball joints push the outer knuckle down, restoring the control arm back to its optimal horizontal resting plane. This brings back a negative camber gain curve during cornering, forcing the front tires flat against the track to kill understeer. Second, because the high-durometer hardened rubber inner bushings cannot deflect or compress sideways like mushy factory rubber, your track and caster settings remain completely locked under heavy braking zones, ensuring predictable front-end stability at high speeds.
Professional Lift Installation & Alignment Notes
Technical Fitting Note: The Hardrace Q0241 kit is designed as a direct structural replacement for the factory front control arm assemblies. Because this kit alters your front roll center height, tracking geometry, and camber tracking lines simultaneously, a professional four-wheel laser alignment is strictly mandatory immediately following installation.
To extract the maximum performance from your new alignment curves, the final tightening sequence for the inner chassis bushing bolts must be performed only while the vehicle is resting under its own full weight at natural ride height on a drive-on hoist or alignment rack. Tightening the suspension arm pivots while the car is hanging in the air twists the rubber bushings permanently, leading to premature bushing failure and an inaccurate ride height. You can schedule a precision setup appointment at our fully equipped JDMaster.net workshop, where our technicians specialize in geometry correction and high-performance track alignment indexing.
Warranty
The warranty on Hardrace products depends on the type of product, with a minimum warranty period of 2 years. This warranty does not cover damage caused by a car crash, improper use, negligence or normal wear and tear.
Warranty by product type
| Rubber bushes | 5 years |
| Spherical bushes | 2 years |
| Adjustable arms with rubber inserts | 5 years |
| Adjustable arms with spherical inserts | 2 years |
| Engine mounts | 5 years |
| Sway bars | Lifetime warranty |
| Bushes and endlinks | 5 years |
| Billet inserts | Lifetime warranty |
| Chassis brace | Lifetime warranty |
| Ball joints/tie rods | 2 years |
| Weight | 8.745 kg |
|---|---|
| Dimensions | 54.5 × 16.7 × 38.2 cm |
Related products
Suspension









