Hardrace Front Lower Control Arm & Roll Center Adjuster – Subaru BRZ / Toyota 86
€917.68 Original price was: €917.68.€780.03Current price is: €780.03.
Pillow Ball Equipped
2 PCS/SET
Available – Delivery within 15 days
Hardrace Front Lower Control Arm & Roll Center Adjuster – Subaru BRZ / Toyota 86 (8814)
Product Overview
The Subaru BRZ and Toyota 86 platforms are celebrated for their low center of gravity and razor-sharp handling balance. However, when these vehicles are lowered on performance coilovers, the angle of the factory front control arms shifts sharply upward. This geometry distortion drops the vehicle’s structural roll center below the ground, increasing body roll, causing erratic toe changes over mid-corner bumps (bump-steer), and causing soft factory rubber bushings to deflect heavily under load.
The Hardrace Front Lower Control Arm & Roll Center Adjuster Kit (8814) is a premium, motorsport-grade suspension solution engineered to eliminate these architectural bottlenecks. Available at JDMaster.net, these high-strength control arms are fabricated from ultra-rigid hardened steel alloy and come pre-assembled with Extended Roll Center (RC) Adjuster ball joints and zero-tolerance spherical pillow ball bushings. By dropping the outer suspension pivot points back down into their mathematically optimal plane and completely eliminating bushing flex, this kit locks down your steering trajectory, keeping your front tires flat against the tarmac at the absolute track limit.
Key Features & Benefits
-
Integrated Roll Center Correction: Built with extended-shank outer ball joints that naturally level out the control arm angle on lowered vehicles, raising the roll center closer to the center of gravity to minimize body roll.
-
Zero-Deflection Spherical Pillow Balls: Loaded with high-hardness metal spherical bearings rather than flexible rubber or polyurethane. This ensures absolute alignment tracking stability under intense cornering and heavy braking zones.
-
Eliminates Dynamic Bump-Steer: Keeps the front steering tie-rods and control arms moving along synchronized, parallel arcs, preventing abrupt, unwanted toe alignment shifts when riding circuit curbs.
-
Reinforced Hardened Steel Alloy: Fabricated from thick-walled, high-tensile steel plates that completely resist twisting and mechanical warping under sticky racing slicks and high-downforce setups.
-
Instantaneous Steering Communication: Removing all bushing compliance creates a direct mechanical pathway between your front crossmember and the steering knuckles, delivering telepathic steering turn-in and precise driver feedback.
-
ED Anti-Corrosion Finish: Treated with Hardrace’s signature Electrophoretic Deposition (ED) base layer and industrial outer paint to provide a durable barrier against stone chips, moisture, and track grit.
-
Direct Bolt-On Configuration: Retains the factory architecture, packaging seamlessly with your OEM or aftermarket coilovers, stabilizer end links, and subframe pick-up points.
Technical Specifications
| Feature | Specification |
| Brand | Hardrace |
| Part Number / SKU | 8814 |
| Product Type | Hardened Steel Front Lower Control Arms with RC Adjusters |
| Bushing Configuration | Zero-Tolerance Motorsport Spherical Pillow Ball Bearings |
| Ball Joint Profile | Pre-Installed Extended Stem Roll Center (RC) Ball Joints |
| Material Base | Ultra-High-Strength Reinforced Steel Alloy |
| Piece Count | 2 Pieces / Set (Complete Front Axle Left & Right Arms) |
| Finish Protection | Industrial Anti-Rust Electrophoretic Deposition (ED) Coating |
| Maintenance Profile | Sealed ball joints with high-elasticity protective dust boots |
| Installation Status | Direct OE replacement (Professional tracking alignment mandatory) |
Applications
-
Subaru BRZ (2012–2021 1st Gen — ZC6 Chassis)
-
Subaru BRZ (2022–Present 2nd Gen — ZD8 Chassis)
-
Toyota 86 / GT86 (2012–2021 1st Gen — ZN6 Chassis)
-
Toyota GR86 (2022–Present 2nd Gen — ZN8 Chassis)
-
Scion FR-S (2012–2016 ZN6 Chassis)
The Mechanical Advantage: Restoring the Lowered Roll Center
When you lower an 86 or BRZ, the physical distance between the chassis subframe and the wheel hub is reduced, forcing the outer ball joint higher than its stock horizontal plane. This creates an elongated “roll couple”—the imaginary lever arm between the vehicle’s center of gravity and its suspension roll center. A longer roll couple means the car will naturally want to lean much harder into corners, forcing drivers to compensate with excessively stiff springs or overly aggressive anti-roll bars that can ruin overall compliance and tire traction.
The Hardrace 8814 kit corrects this issue purely through mechanical geometry. By integrating an extended ball joint stem, it pushes the front lower control arm back down into its natural operating plane. This raises the roll center back up closer to the car’s center of gravity, shortening the roll couple and naturally reducing body roll using pure physics. Combined with solid metal spherical pillow balls that replace flexible factory rubber at the inner pivots, steering wheel input translates immediately to razor-sharp front-end direction changes with zero compliance lag or calculation delay.
Professional Lift Installation & Alignment Notes
Technical Fitting Note: The Hardrace 8814 kit is an intense, track-focused suspension upgrade featuring solid metal spherical pillow ball bushings. Because these bearings lack the dampening compliance of soft factory rubber, a minor increase in road noise, vibration, and harshness (NVH) will be transmitted into the cabin over sharp bumps—the standard, industry-wide trade-off for zero deflection and precise track feedback.
Because this kit alters your vehicle’s structural roll center height, tracking index, front track width, and camber lines simultaneously, a professional four-wheel laser alignment is strictly mandatory immediately following installation. You can schedule a precision chassis indexing and setup appointment at our fully equipped JDMaster.net workshop, where our alignment specialists tailor geometry for fast road, time attack, and circuit performance.
Warranty
The warranty on Hardrace products depends on the type of product, with a minimum warranty period of 2 years. This warranty does not cover damage caused by a car crash, improper use, negligence or normal wear and tear.
Warranty by product type
| Rubber bushes | 5 years |
| Spherical bushes | 2 years |
| Adjustable arms with rubber inserts | 5 years |
| Adjustable arms with spherical inserts | 2 years |
| Engine mounts | 5 years |
| Sway bars | Lifetime warranty |
| Bushes and endlinks | 5 years |
| Billet inserts | Lifetime warranty |
| Chassis brace | Lifetime warranty |
| Ball joints/tie rods | 2 years |
Related products
Suspension





