Hardrace Front Lower Arm (Pillow Ball) – Honda Integra DC5

Hardrace Front Lower Arm (Pillow Ball) – Honda Integra DC5 (Q0465)

Product Overview

The DC5 chassis utilizes a MacPherson strut front suspension layout that is highly sensitive to changes in ride height. When you lower this chassis on performance coilovers, the factory front control arms angle sharply upward. This geometry shift drops the vehicle’s structural roll center below the ground, severely increasing body roll and causing the front tires to toe out unpredictably as the suspension compresses (bump-steer).

The Hardrace Front Lower Arm Kit (Q0465) is a heavy-duty, track-focused chassis upgrade engineered specifically to solve these inherent layout flaws on vehicles utilizing M14 ball joint knuckles. Available at JDMaster.net, these arms are manufactured from ultra-high-strength hardened steel and come pre-assembled with integrated Roll Center (RC) adjusters and zero-tolerance spherical pillow ball bushings. By correcting the physical pivot points of your front suspension, this kit restores ideal tracking mechanics, delivering immediate steering precision and maximum tire adhesion under heavy track loads.

Key Features & Benefits

• Integrated Roll Center Correction: Features extended-stem lower ball joints that level out the control arm angle on lowered vehicles, raising the roll center closer to the center of gravity to reduce body roll.

• Eliminates Bump-Steer: Keeps the front steering tie-rods and control arms moving along parallel arcs throughout their suspension travel, preventing sudden toe alignment changes over mid-corner bumps.

• Motorsport Spherical Pillow Balls: Replaces flexible factory rubber or polyurethane pivots with solid metal spherical joints, ensuring zero arm deflection under extreme braking and cornering.

• Laser-Sharp Steering Turn-In: Removing bushing compliance creates a direct mechanical pathway between the front crossmember and the steering knuckles for instantaneous driver feedback.

• Hardened Steel Construction: Fabricated from thick, high-tensile hardened steel to safely withstand structural loads from sticky racing slicks and high-downforce circuit setups.

• Premium ED Coating Finish: Finished with an advanced Electrophoretic Deposition (ED) treatment to provide excellent resistance against corrosion, moisture, and track debris.

Technical Specifications

Applications

This front control arm kit features an M14 ball joint mounting hole profile. Please verify your knuckle configuration prior to purchase, as ball joint taper diameters vary across different model years:

• Honda Integra / Acura RSX Type S (2005–2006 Facelift Models)

• Honda Integra Type R JDM (2001–2006 DC5 Chassis — Note: Fits factory JDM Type R aluminum knuckles utilizing the M14 ball joint hardware configuration)

The Mechanical Advantage: Restoring MacPherson Strut Efficiency

On a standard MacPherson strut design like that of the DC5 Integra, the lower control arm acts as the primary mechanical anchor for the wheel hub. When the car is lowered without correction, the arm tilts past its horizontal horizontal line. When you throw the car into a hard corner, the suspension compresses further into a positive camber curve, which lifts the inner edge of the tire off the tarmac and severely shrinks your contact patch.

The Hardrace Q0465 kit addresses this bottleneck on two fronts. First, the extended-stem roll center ball joints push the outer knuckle down, restoring the control arm back to its optimal horizontal resting plane. This brings back a negative camber gain curve during cornering, forcing the tire flat against the track. Second, because spherical pillow balls cannot compress or shift sideways like factory rubber, your caster and track settings remain completely locked under heavy braking zones, ensuring predictable front-end stability at high speeds.

Professional Lift Installation & Alignment Notes

Technical Fitting Note: The Hardrace Q0465 control arms feature a specific M14 ball joint taper. Attempting to bolt these into pre-facelift or standard base-model hubs designed for smaller M12 ball joints (which require the Q0464 kit) will result in component mismatch and unsafe suspension assembly. Always verify your steering knuckle’s hardware diameter before installation.

Because this kit alters your front roll center height, tracking geometry, and camber tracking lines simultaneously, a professional four-wheel laser alignment is strictly mandatory immediately following installation. You can schedule a precision setup appointment at our fully equipped JDMaster.net workshop, where our technicians specialize in MacPherson geometry correction, track day setups, and high-performance suspension indexing.

Warranty

The warranty on Hardrace products depends on the type of product, with a minimum warranty period of 2 years. This warranty does not cover damage caused by a car crash, improper use, negligence or normal wear and tear.